揄拍成人国产精品视频_aaaaaa级特色特黄的毛片_天干夜天天夜天干天2004年_欧美人与物ⅴideos另类_国产精品中文字幕自拍

粘度計|旋轉粘度計廠家|運動粘度計|烏氏粘度計廠家_上海標卓

主頁 > 使用方法 >

粘度計英文使用說明書

 

This instrument is widely supplied in measuring axunge paint plastic, food, medication, adhesive, cosmetic and so on like fluidic sticky resistance and liquid absolute viscosity.fix and measuring must be done according requirement from instruction book。
 
Main technic spec
 
·Range of measure:10~105mpa.s
·Rotate speed: 6,12,30,60turn/minute
·Error of measure:±5%(Newton liquid)
·Power:220V±10%
         50Hz
 
Fix

1.     take out chassis base
andsupport from packing
boxcircumrotate three
level 。
2.adjust foot into tapping
hole in chassis base(chart 1)
3.main machine fix:
a. take out main machine by unscrewing the screws in chassis
b. unscrew the handle root screw . inset the power line into handle slot(chart2)
c. penetrate the handle into hole under slot(chart2)
d. screw the handle fix knob to screw the handle and keep the main machine level mostly (chart3)
 
 
8.measure the temperature of measured liquid directly , do not use the temperature value of constant temperature bath
9. it is normal when the viscosity changes because of change of speed and length of measure time during measuring. That is not the instrument hitch.
10.operate seriously according the operation manual
 
 

The whole set

1.main machine————————1
2.(1,2,3,4)rotors———— 1
3.protective support—————— 1
4.support——————————  1
5.lever adjustment screw———— 3
6.manual——————————  1
7.certificate ————————— 1
 
Quotiety table
 
     Run/minute
rotor
60 30 12 6
1 1 2 5 10
2 5 10 25 50
3 20 40 100 200
4 100 200 500 1000
 

 

Notice

1.this instrument should be used in 10—30
2.protective support must be fixed when measuring, or the viscosity value will change as the change of diameter of container
3.the rotor connective screw staff should be raised when fix or remove rotor, or the head of shaft will be damaged. Keep the bleb from rotor when rotor is immerged into liquid
4.the instrument should not be placed in oblique or inverse direction. Especially the rotor is fixed.
5.after fixing the rotor, do not turn on machine to turn the rotor without immerging the rotor into liquid
6.remove rotor carefully after finishing work every time.  Clear it extremely, dry is with blower, and put it back on the rotor support in vertically
7.pointer lock staff should be packaged by yellow package cover and rubber hand when carrying the instrument.
 


 
e. remove the rubber hand from pointer lock staff and yellow package cover from main machine inferior part.
alarm: do not turn on machine before removing the above two objects or it will damage the machine
power on, adjust the level adjustment foot(chart4). Make the bleb in the middle of level set(chart5).
 
Operation
 
1.first rightly rotate the protective support into the instrument inferior part.
2.prepare the liquid for measuring, select the column container having diameter not less than 70 mm
3.control the temperature in liquid for measuring correctly according the precision required by measuring
4. select the right rotor number by estimating the approximate range of viscosity of liquid or measuring, and rotate left the rotor into the connective screw staff(chart4),then rotate the up and down knob(chart5),make the instrument down slowly, immerging into measured liquid gradually, until the rotor liquid level balances the liquid level(chart4).put down the pointer lock staff, power on, relax.

the pointer lock staff,
to make the rotor
circumrotate in the
liquid. The speed is
20-30 run, until the
pointer stay at one
position . put down
the pointer lock staff to
make the reading unchangeable,
then turn off the motor to
make the pointer stay
in the range of reading
window,then get the
reading directly. If the
pointer do not stay in
the frame after turning
off motor, go on to put
down the pointer lock
staff. Repeat the action 
of turning on and off to
make the pointer in the
frame of window. If
selecting 6 and 12 turn /minute,
get the reading directly
without locking the pointer.5.the best is that the read pointer stay 30—90 division range, or change the rotor number or run speed to get the requirement 6.when you can not predict the viscosity value of liquid for measuring , the rotor and turn speed knob should be selected by turning from little value to big value, and from slow to fast, to measure the viscosity value.
 
 
Quotiety  and error correcting
1.the absolute viscosity value of liquid measured can be get by multiplying the reading pointed on dial when measuring and quotiety in quotiety table
that is:
η(mpa.s=k×α
k= quotiety
α=pointer reading
η=viscosity value
2.frequency error correcting
                                     normal frequency
actual viscosity value= indicated value ×—————————
                              actual frequency
 
 

 

Range stable and quotiety table

range stable
rotor Turn/minute
60 30 12 6
1 100 200 500 1000
2 500 1000 2500 5000
3 2000 4000 10000 20000
4 10000 20000 50000 100000
 
 
 

 


[上一篇:烏氏粘度計原理及其應用 ]    [下一篇:美國 BROOKFIELD博勒飛粘度計使用說明書 ]

使用方法

常見問題

瀏覽更多同類產品

STM-IVB斯托默粘度計
STM-IVB斯托默粘度計
 NDJ-1E 旋轉粘度計
NDJ-1E 旋轉粘度計
NDJ-1D 布氏旋轉粘度計
NDJ-1D 布氏旋轉粘度計
烏氏粘度計
烏氏粘度計
亚洲日韩成人av无码网站| 日韩内射美女人妻一区二区三区| 亚洲の无码国产の无码步美| 中文字幕亚洲国产精品| 久久精品国产只有精品96| 久久99国产精品久久| 人妻一本久道久久综合久久鬼色| аⅴ资源中文在线天堂| 丰满多毛的大隂户视频| 美女网站免费观看视频| 国产伦精品一区二区三区视频三级| 欧美怡春院一区二区三区| 桔子av一区二区三区| 亚洲熟妇av一区二区三区宅男 | 亚洲乱亚洲乱妇无码麻豆| 又紧又大又爽精品一区二区| 日韩欧美高清dvd碟片| 亚洲精品无码久久久久av麻豆| 久久久久99精品国产片| 性视频播放免费视频| 国产性生交xxxxx无码| 久久日本三级韩国三级| 18禁女裸乳扒开免费视频| 欧美人与禽猛交狂配| 麻豆妓女爽爽一区二区三| 亚洲日韩精品欧美一区二区一| 蜜桃传媒av免费观看麻豆 | 女人高潮被爽到呻吟在线观看 | 黄片一区视频在线免费观看| 成年女人毛片免费观看97| 午夜福利啪啪片| av综合网男人的天堂| 欧美俄罗斯40老熟妇| 国产全肉乱妇杂乱视频| 精品人妻伦九区久久aaa片69| 女人扒开屁股爽桶30分钟| 亚洲人妖一区二区三区| 免费看a级肉片| 国产精品福利一区二区久久| 少妇高潮惨叫久久久久久| 久久国产精品偷|